The following are USED parts that I have removed from my parts cars and/or projects.

• 1961 - 1964 409 Oil Pan #1.
  
  This is a used oil pan from a 409. It will also fit a 348 but the dipstick hole is on the opposite side. This pan appears to have had some water laying in it for a while. As a result there is quite a bit of surface rust on the inside as well as 2 or 3 small holes in the bottom. There are also a few small dents and dings in the bottom. More photos available upon request.
  Price: SOLD
  

  ---

  
  
• 1961 - 1964 409 Oil Pan #2.
  
  This is another used oil pan from a 409. At one time, the front portion of the sump in this pan was cut out for chassis clearance. A section of the sump from an old 348 truck pan was cut and welded onto this pan to bring it back to it's original shape. Some Evercoat Metal2Metal filler was used to smooth over the outside of the weld seam. The outside was sprayed with gray primer and the inside with silver paint to prevent surface rust. As a result of the sump repair this pan no longer has a baffle inside and the drain plug is on the bottom in the truck (as opposed to passenger car) location. More photos available upon request.
  Price: $100 + shipping
  

  ---

  
  
• 1963 - 1965 340HP 409 Pistons. This is a set of 8 used original 10:1 standard size pistons from a 63 340HP 409. One of the pistons has a chunk broken off the lower skirt area. The other 7 look okay.
  Price: $20 + shipping
  

  ---

  
  
• Miscellaneous 194/230/250 inline 6 cylinder engine parts.
  These include:
  • Cylinder Head
    
    Head casting #3864886. Off a 250. Includes valves, springs, and rocker arms. Valve cover sold separately.
    Price: $25 + shipping
  • Valve Cover Shown above. No significant rust or dents.
    Price: $10 + shipping
  • HEI Distributor
    
    Off a 75/76 6-cyl. Shaft turns freely. Could stand to be disassembled and thoroughly cleaned. Has wiring connector for 75/76 style external coil but could easily be changed over to the 77-up coil in cap setup. Includes plug wire retainer that snaps onto the cap. Does NOT include a module or coil.
    Price: $25 + shipping
  • Another HEI Distributor Same as the one listed above but does not include the plug wire retainer for the cap. This one has a little bit of surface rust on the lower shaft & gear (should easily clean off with a wire wheel).
    Price: $20 + shipping
  • Intake Manifold (Off a 1974 250, for 1bbl carb, non-integral head, includes EGR valve)
    Price: SOLD
  • Harmonic Damper (has built-in 2-groove pulley)
    Price: $15 + shipping
  • Oil Pump Pick-up Tube & Screen (oil pump NOT included)
    Price: $5 + shipping
  • Engine Mount Brackets (upper halves that bolt to the engine block & mate up with "clamshell" type frame mounts, frame mounts NOT included)
    Price: $8 + shipping
  • Engine Oil Dipstick (tube NOT included)
    Price: $2 + shipping
  • Alternator Brackets (both upper & lower, I believe the upper one is for a NON-power steering setup)
    Price: $8 + shipping
  
  

  ---

  
  
• 1968 - 1974 Nova Upper and Lower Control Arms (A-arms).
  These have heavy rust pitting. Might be useful for chassis mock-up purposes and/or testing modifications prior to committing the design to a good set of A-arms.
  Price: $40 (for all 4) + shipping
  

  ---

  
  
• 1973 - 1974 Hood lip molding.
  
  In decent used condition. Has a few small nicks and dings. Would be good as-is on a "driver" but would need to be refurbished for use on a "show car". All mounting studs are still in place but there is one that is loose. It will still accept a nut and hold the molding secure but it will need to be held with some needle nose pliers or something to keep it from spinning while tightening the nut.
  Price: SOLD
  

  ---

  
  
• 1973 - 1974 LH remote control mirror. This is a rectangular chrome LH door mirror from a 73 Nova. The chrome on the mirror housing is in decent condition but inside control lever is damaged. Includes the mirror, mounting hardware/gasket, control cables, and lever. Does not include the inside door panel bezel for the control lever.
  Price: SOLD
  

  ---

  
  
• 1977 Nova factory AC parts.
  
  I don't know if this system was still functional but all parts are intact except for the radiator support, which is rusted out. I'll part this system out as follows:
  • Compresor brackets.
    Price: SOLD
  • Compressor and hoses for 250 inline 6 engine. Should fit 75 - 79 (may also fit older Novas).
    Price: $15 + shipping
  • Condenser core. Fits 75 - 79. Will also fit a V8 car.
    Price: $35 + shipping
  • Evaporator core and firewall case assembly (underhood part). Fits 75 - 79. Will also fit a V8 car. Might also fit 68 - 74.
    Price: $45 + shipping
  • Fan shroud. Fits 6-cylinder with AC and/or heavy duty cooling system.
    Price: $15 + shipping
  • Instrument panel housing w/AC vent.
    Price: SOLD
  • Heater/AC control panel, switches, and cable. Fits 77 - 79.
    Price: SOLD
  • Under dash heater box and plastic AC ductwork. Fits 77 - 79 (some parts may fit earlier years).
    Price: $30 + shipping
  • Pair of AC kick panels. Blue. Good condition. Includes the vacuum operated flap door on the RH panel. Lower flange (next to carpet) on RH panel has a broken chunk about 2" long. I'll include the broken section so it can be glued back into place.
    Price: $35 + shipping
  • AC outside air inlet door. This is the vacuum operated flap door that mounts to the passenger side of the cowl and controls the intake of outside air.
    Price: $10 + shipping
  • AC wiring harness. This is the harness that plugs into control switch, pressure cut-out switch, blower motor, compressor clutch, and other AC components. Fits 77 - 79 and may work on earlier years with modifications.
    Price: $20 + shipping
  • Dash pad. Blue. No cracks. Includes center and RH AC vents. Fits 77 - 79.
    Price: SOLD
  
  

  ---

  
  
• 77 - 79 Nova instrument cluster.
  
  I have one of these instrument clusters left. It has a working speedometer. The gas gauge likely works too but is untested. It is the regular style cluster (no clock, no tach, no temp gauge, etc). It was removed from an automatic transmission car so it has the "PRND21" indicator. Clear plastic lens is included but the outer dash bezel is sold separately (see below).
  Price: $25 + shipping
  

  ---

  
  
• 77 - 79 Nova instrument panel outer bezel.
  
  This instrument panel bezel is from a non-A/C car. The radio opening is uncut but there are a couple of broken pieces at each top corner. The pieces could be glued back in place and shouldn't be that noticible once the bezel is installed.
  Price: $35 + shipping
  

  ---

  
  
• 69 - 74 Nova AM radio. Has not been tested. Sold AS-IS. Does not include any knobs or mounting cups. Will also fit 75 - 76.
  Price: $10 + shipping
  

  ---

  
  
• 75 - 77 Nova steering wheel.
  
  Good used steering wheel removed from a 77 Nova. The black metal horn button insert is a little faded around the "Nova" lettering, the grain texture is a bit worn around the outer rim, and it could use a good cleaning. Includes the horn button/pad. Style is correct for 75 to 77 Novas but will fit other years.
  Price: 25 + shipping
  

  ---

  
  
• 78 - 79 Nova steering wheel.
  
  Very nice used steering wheel removed from a 78 Nova. Still has most of the grain texture present. Includes the horn button/pad. Style is correct for 78 and 79 Novas but will fit other years.
  Price: 35 + shipping
  

  ---

  
  
• 78 - 79 Nova wheelcovers.
  
  Set of 5 wheelcovers in good condition with a few minor scratches and dings. Some of them could use a good cleaning and polishing and some of the center emblems are a little faded.
  Price: SOLD
  

  ---

  
  
• 75 - 79 Nova interior door handles & cups. I have several of the chrome inside door handles and a few of the black plastic trim cups that go under them. Some of the chrome handles have some light pitting/scratches.
  Handles: $9 each (or $15 for a left/right pair) + shipping
  Cups:
  
  • Left (driver side): $4 (1 available ... has broken screw hole but can still be mounted using a larger head screw or washer)
  • Right (passenger side): $7 each (4 available)
  
  

  ---

  
  
• 1971 - 1974 Pontiac Ventura dash pad emblem.
  
  This is a good used Pontiac emblem that was removed from a 73 Ventura dash pad. It will fit all 69-74 Nova/Omega/Ventura/Apollo style dash pads. It measures about 1" x 3".
  Price: $10 (includes postage in continental US)
  

  ---

  
  
• 73 - 74 Nova 4 door parts:
  Window regulators:
  Note: These will only fit 4-door cars.
  LH Front = still available
  LH Rear = still available
  RH Front = still available
  RH Rear = SOLD
  Price: $15 each + shipping
  
  Door latch mechanisms:
  Note: These will only fit 4-door cars.
  All 4 still available
  Price: $15 each + shipping
  

  ---

  
  
• 73 - 74 Nova 4-door front and rear seats. Color: tan. They're in good condition (came from a 25,000mi parts car).
  Below is a photo of my car that shows the front seat (I used it temporarily until I found the correct 2-door seat).
  
  These seats are too large/bulky to ship UPS or FedEx -- I could ship them truck freight but that's VERY expensive. For local (Northern Maine) pickup only.
  Price: $60
• 73 - 74 Nova 4-door windshield and rear window. These should also fit 68-72 4-door Novas. They are too large and fragile to ship safely. For local (Northern Maine) pickup only.
  Price: make an offer
  

  ---

  
  
• 73 - 74 Nova 2 door aluminum body side molding. Some minor dents/dings. Black paint is missing off the center portions of the door and quarter panel pieces (should be easy to re-paint though). Will also fit 69 - 72 Nova.
  
  Price: $40 + shipping
  

  ---

  
  
• 65 or 66 Impala SS & 65 Nova SS wheel covers.
  
  I believe these wheelcovers fit 1965 Impala & Nova SS and possibly 1966 Impala SS. These fit 14" wheels. I only have 3 of these and they are in okay condition. There is some pitting on the chrome and some scuffs/scratches/dings.
  Price: $30 + shipping
  

  ---

  
  
• 1970's "dog dish" hub caps.
  
  These came off a 1970 Malibu. They fit 14" wheels (only cover the smaller center section). I only have 3 of these and they are in okay condition. Some are better than others but they all have some dents and dings.
  Price: $25 + shipping
  

  ---

  
  
• 67 - 68 Camaro/Firebird heater control panel.
  
  There are no broken parts and the temperature and defroster levers move freely. The air/fan lever is a little stiff as it moves through the fan speeds.
  Price: $10 + shipping
  

  ---

  
  
• Unknown 70's/80's Bumper Guards.
  
  I'm not sure what these fit. Probably a late 70's or 80's car. Chrome is in good condition as are the hard plastic/rubber pads. Each one has a 10mm threaded mounting stud on the back along with a mounting tab at the bottom.
  Price: $10 + shipping
  

  ---

  
  
• 1960 - 1963 Chevrolet truck instrument cluster with factory gauges and tachometer.
  
  
  This instrument cluster with a rare factory tachometer (made by Sun for GM) was removed from a 1962 C80 truck. I believe it will fit 1960 through 1963 Chevy trucks. Includes the Sun EB-9A, 12Volt, 8Cyl transmitter box and all associated wiring. Also includes the under-dash wiring harness which will be needed if using this cluster to replace a warning light cluster. The under-dash harness has a couple of wires that need to be repaired/replaced but it hasn't been cut up or modified. A Signal-Stat 4-way hazard flasher is also included with the wiring.
  Price: $400 + shipping
  

  ---

  
  
• 1967 - 1972 Chevrolet truck factory AC parts.
  
  This is a nearly complete factory AC setup removed from a 1971 Chevy pick-up truck. Includes the evaporator and condenser cores, heater box, under-dash ductwork, in-dash control panel and dash vents, wiring harness, and other miscellaneous parts. Not shown in the photo but also available is the compressor and most of the brackets necessary to mount it to a small block V8 engine. The wiring harness does have a few cut wires that need repair. Will sell as a complete set-up or as individual pieces.
  Price: $350 + shipping for the whole set-up
  

  ---

  
  
• 1973 - 1978 Chevrolet/GMC pick-up truck headlight bezels.
  Photo comming soon
  These are a pair of very good used headlight bezels. There is some minor pitting on the chrome but they are still very shiny. The recessed center areas have been re-painted dark gray. These are original metal bezels ... not plastic reproductions.
  Price: $35 + shipping
  

  ---

  
  
• More 1973 - 1978 Chevrolet/GMC pick-up truck headlight bezels.
  
  
  In addition to the set listed above, I have two more pairs of these 73-78 Chevy/GMC pick-up truck headlight bezels. These two pairs aren't quite as nice though. They have more pitting and the chrome isn't as shiny. Should be good for a daily driver or work truck though. The recessed center areas need to be re-painted. These are original metal ... not plastic reproductions.
  Price: $10 per pair + shipping
  

  ---

  
  
• 1979 - 1980 Chevrolet/GMC pick-up truck headlight bezels. These are a pair of good used headlight bezels for all 79 and 80 trucks with round headlights. There is some pitting on the chrome but they are still quite shiny. The recessed center areas could stand to be re-painted. These are original metal ... not plastic reproductions.
  Price: SOLD
  

  ---

  
  
• Another pair of 79-80 Chevy/GMC pick-up truck headlight bezels.
  
  This is a slightly used pair of plastic reproduction bezels for 79-80 Chevy/GMC pick-up trucks with round headlights. The "chrome" plating is still nice but some of the paint on the center recessed area of one bezel is peeling a little.
  Price: $20 + shipping
  

  ---

  
  
• 1973 - 1974 Chevrolet pick-up truck grilles.
  
  
  I have two 73/74 Chevy truck grilles. The one in the top photo has "chrome" around the outer edge and is in good condition. It has some scuffs/scratches on the silver painted center section but no cracks or missing pieces. It also includes a 350 engine displacement emblem. Both the 350 and Chevy emblems are faded.
  The grille in the bottom photo doesn't have the "chrome" around the edge and has a missing horizontal bar section on the passenger side. It also has some small chips along the lower edge and does not include an engine displacement emblem (but has provisions to mount one). The Chevy emblem in the center of this grille is faded/dull too.
  Note: UPS Oversize shipping charges apply to these grilles.
  Price: SOLD (chrome edge grille in top photo)
  Price: $25 + shipping (other grille in bottom photo)
  

  ---

  
  
• 1973 Chevrolet/GMC pick-up truck radiator overflow and windshiled washer reservoirs.
  
  Plastic radiator overflow and windshield washer reservoirs removed from a 73 Chevy pick-up truck. I believe the radiator overflow tank is correct for 73 only (later years used a different style). The windshield washer tank is also specific to 73 (and possibly 74/75). It slides into a special slot in the fender so it won't fit trucks with 76-80 style replacement fenders.
  Price: $10 + shipping
  

  ---

  
  
• 1973 - 1980 Chevrolet/GMC pick-up truck hood hinges. I have several sets of good used hood hinges for these trucks. They all have some minor surface rust but should clean up nice.
  Price: $25 per pair + shipping
  

  ---

  
  
• Old Radios.
  
  Both of these radios are untested and being sold as-is. I've been told the Motorola radio is an aftermarket unit that will fit a 1956 Chevy. I believe the Chevy radio fits 1953 and 1954 cars and is correct for 54.
  Price: $25 each + shipping
  

  ---

  
  

Please contact me at: ray_mcavoy@yahoo.com if you would like to purchase any of these parts.